CDMA-Tool v1.43 released:

.ZTE-C1602 model supported
.Huawei-C2809 model supported (firmware version B105 and B106)
.new smard-card types supported
.many small but important internal changes



As ordinary, non-stop free (no any additional payments required) updates during last 6 years, as nobody else...

Infinity-Box 6 (six) years non-stop free updates and support: Infinity-Box - News
- World biggest flash files database for several thousands brands/models
- Infinity-Box Variants & Packages
- BB5 Easy Service Tool [BEST] Dongle
- CDMA-Tool Dongle (fast and easy unlock)
- PinFinder: automatic pinout detection device
- Language & Resource Editor for MT62xx based models
- Extract phonebook (and other content) from alive and dead phone
- Follow us on Twitter

Doing Service in Mobile or Mobile Service desperately needed understanding of what tools will we use it, especially if it is about software, this software because it takes a very understanding More than On When To deepen understanding of the field of Hardware.:.

Tornado UFS TECHNIQUES

Tips and tricks Using Nokia UFS3 Tornado On

In the case of 1st Boot Err or Bad Resp DCT3

Such damage is not usually occur because the phone connection of the Box

Check Flasher cable is used, because there is no possibility of being cut off point

If the cable is in good condition, there is the possibility of damage on the software UFS3

Reinstall the program with data that is still nice

Contact Service at Case

Damage like this is usually because they damage the data

Make a data deletion process with Erase FLASH

Then do flashing with the data is still good

Put a tick in the UI Options and click the Settings button UI

If there is damage to the IMEI data, do the Rebuild IMEI and repeat the process UI Settings

If the damage due to hardware, there are some IC that causes it, but cases like this simply by replacing the IC or IC Audio COBBA


If sata or Erasing Flashing process, the process stalled

Check Flasher cable, because it shows the relationship between the disconnection of telephone service provider with Flasher Box

Repeat process with reducing speed Speed Flasher

If it still stops at the same position repeatedly, there is the possibility of disturbance Flash IC

In case of contact Phone failed blimking retailer or on the phone type of WD2

Make sure your phone is connected well with UFS3 Tornado Box

UFS3 Tornado Run programs for Nokia phones and select the type of WD2

Choose a type mobile phone that is being repair

Click Connect button to liaison between the Box UFS3 Tornado with Computers

Click the button to make sure Chek phone had been connected "Boot Ok"

In the UI Settings tab select Normal column, wait until the Normal Mode Ok

After appearing on the screen Normal Mode Ok continue by pressing the Format User Area

Finish Process

Practical Solutions Contact retailer or Blimking on your Nokia 6600

If this happens Flashing Erase error

Click Erase FLASH with the provisions of the Start Address and End Address 027FFFFF 02000000

If there Erase Flash Error then have to replace the flash IC No. 2, of the four existing IC

If the process successfully, but when switched on is still on the Contact retailer

Raise battry and plug in, then press the Call button in a cell phone or green button * number three in the mobile phone by simply pressing buttons simultaneously, without the use simcard

After the above step has been done, then the phone will do formating

After doing the formatting, mobile phones have been ready for use

In the case of Simcard Rejected or Simcard rejected a common cell phone types and DCT-4 WD2

Make sure your phone is connected well with UFS3 Tornado Box

UFS3 Tornado Run programs for Nokia phones and select the type or DCT-4 WD2

Choose a type mobile phone that is being repair

Click Connect button to liaison between the Box UFS3 Tornado with Computers

Click the button to make sure Chek phone had been connected "Boot Ok"

In the UI Settings column select Normal, Normal Mode Ok wait until

After appearing on the screen Normal Mode Ok proceed by giving the tick on the Init Simlocks contained in the columns UI Options

Then click the Settings button until you see the UI on the screen Ok Init Simlock

In the case of No Charging and No Signal On Cell Phone and DCT type-4 WD2

Make sure your phone is connected well with UFS3 Tornado Box

UFS3 Tornado Run programs for Nokia phones and select the type or DCT-4 WD2

Choose a type mobile phone that is being repaired

Click Connect button to liaison between the Box UFS3 Tornado with Computers

Chek Click the button to make sure the phone had been connected "Boot Ok"

In the UI Settings tab select Normal column, wait until the Normal Mode Ok

Click the button write pm (Wr PM), only one times with the provisions have saved PM file from each phone in the directory (c: \ Program Files \ Nokia \ Phoenix \ Products)

Wait until the process is complete

Phone Locks To overcome the problem of the phone type Nokia

Make sure your phone is connected well with UFS3 Tornado Box

Run the program for the Nokia UFS3 Tornado

Choose a type mobile phone that is locked or the phone lock

Click Connect button to liaison between the Box UFS3 Tornado with Computers

Click the button to make sure Chek phone had been connected "Boot Ok"

Tick tick on Full Factory Devaults contained in the columns UI Options

Then click the Settings button until you see the UI on the screen Full Factory Devaults Ok

Using tips and tricks UFS3 Tornado On Sony Ericsson phones

Practical Ways Sony Ericsson Flashing

Make sure your phone is connected well with UFS3 Tornado Box

Click Connect button located on the top left of the program

Battery not installed first before pressing the ON button, after pressing ON button you install a new battery, wait until everyone reads all phone information

Choose a type mobile phone that will diflash and select the appropriate type of mobile data is also done

Click the Flash button or Flash MCU Mod Lang or Flash or Flash GDFS or depending on the phone that is being done

How to unlock Z200 Unlock

In this case we can start by pressing the button on the UFS3 Tornado Init Locks

Mereflash followed by re-file "Z200_cust_std.bis by pressing the flash button on the program UFS3 Tornado cust

Or by setting the scenario for selecting Unlock column by pressing the Go button



Flashing Sony Ericsson Z200 Series Type ATRZ

Enter the file or data language such as 200_126734_r6c_con3.bis in Part1 and Part2 200_126734_r6c_fix3 at

Connect the phone with box and press the Go Flasher

Wait until the finish, to end press the Stop button and the phone ready to be released

Flashing Sony Ericsson T610 series RTP Type

Enter the MCU file such as a modem and a file T610_132233_r4c003_Emea6.bis T610_132233_r4c003_modem.bih

Select the column MCU scenario Modem

Connect phone and press the Go button, wait until the process is complete

Click Stop to release phones

Using tips and tricks on Samsung UFS3 Tornado

Make sure your phone is connected well with UFS3 Tornado Box

Click Connect button located on the top left of the program

Choose a type mobile phone that will diflash and select the appropriate type of mobile data is also done

Enter Flasher files according to the type of phones that work

Remove the battery (flash without battery)

Press the button 'Write Flash' is contained in the program and continue UFS3 Tornado by pressing the 'on' on the phone until the flame jgn

Wait until flash process finished

To type a specific phone or cell phone battery while still mounted on the flash time

Hopefully Helpful