REPAIRING TECHNIQUES of UFS tornado Flasher
11:25 AM
Raja Mobile
, Posted in
Doing Service in Mobile or Mobile Service desperately needed understanding of what tools will we use it, especially if it is about software, this software because it takes a very understanding More than On When To deepen understanding of the field of Hardware.:.
Tornado UFS TECHNIQUES
Tips and tricks Using Nokia UFS3 Tornado On
In the case of 1st Boot Err or Bad Resp DCT3
Such damage is not usually occur because the phone connection of the Box
Check Flasher cable is used, because there is no possibility of being cut off point
If the cable is in good condition, there is the possibility of damage on the software UFS3
Reinstall the program with data that is still nice
Contact Service at Case
Damage like this is usually because they damage the data
Make a data deletion process with Erase FLASH
Then do flashing with the data is still good
Put a tick in the UI Options and click the Settings button UI
If there is damage to the IMEI data, do the Rebuild IMEI and repeat the process UI Settings
If the damage due to hardware, there are some IC that causes it, but cases like this simply by replacing the IC or IC Audio COBBA
If sata or Erasing Flashing process, the process stalled
Check Flasher cable, because it shows the relationship between the disconnection of telephone service provider with Flasher Box
Repeat process with reducing speed Speed Flasher
If it still stops at the same position repeatedly, there is the possibility of disturbance Flash IC
In case of contact Phone failed blimking retailer or on the phone type of WD2
Make sure your phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run programs for Nokia phones and select the type of WD2
Choose a type mobile phone that is being repair
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button to make sure Chek phone had been connected "Boot Ok"
In the UI Settings tab select Normal column, wait until the Normal Mode Ok
After appearing on the screen Normal Mode Ok continue by pressing the Format User Area
Finish Process
Practical Solutions Contact retailer or Blimking on your Nokia 6600
If this happens Flashing Erase error
Click Erase FLASH with the provisions of the Start Address and End Address 027FFFFF 02000000
If there Erase Flash Error then have to replace the flash IC No. 2, of the four existing IC
If the process successfully, but when switched on is still on the Contact retailer
Raise battry and plug in, then press the Call button in a cell phone or green button * number three in the mobile phone by simply pressing buttons simultaneously, without the use simcard
After the above step has been done, then the phone will do formating
After doing the formatting, mobile phones have been ready for use
In the case of Simcard Rejected or Simcard rejected a common cell phone types and DCT-4 WD2
Make sure your phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run programs for Nokia phones and select the type or DCT-4 WD2
Choose a type mobile phone that is being repair
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button to make sure Chek phone had been connected "Boot Ok"
In the UI Settings column select Normal, Normal Mode Ok wait until
After appearing on the screen Normal Mode Ok proceed by giving the tick on the Init Simlocks contained in the columns UI Options
Then click the Settings button until you see the UI on the screen Ok Init Simlock
In the case of No Charging and No Signal On Cell Phone and DCT type-4 WD2
Make sure your phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run programs for Nokia phones and select the type or DCT-4 WD2
Choose a type mobile phone that is being repaired
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Chek Click the button to make sure the phone had been connected "Boot Ok"
In the UI Settings tab select Normal column, wait until the Normal Mode Ok
Click the button write pm (Wr PM), only one times with the provisions have saved PM file from each phone in the directory (c: \ Program Files \ Nokia \ Phoenix \ Products)
Wait until the process is complete
Phone Locks To overcome the problem of the phone type Nokia
Make sure your phone is connected well with UFS3 Tornado Box
Run the program for the Nokia UFS3 Tornado
Choose a type mobile phone that is locked or the phone lock
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button to make sure Chek phone had been connected "Boot Ok"
Tick tick on Full Factory Devaults contained in the columns UI Options
Then click the Settings button until you see the UI on the screen Full Factory Devaults Ok
Using tips and tricks UFS3 Tornado On Sony Ericsson phones
Practical Ways Sony Ericsson Flashing
Make sure your phone is connected well with UFS3 Tornado Box
Click Connect button located on the top left of the program
Battery not installed first before pressing the ON button, after pressing ON button you install a new battery, wait until everyone reads all phone information
Choose a type mobile phone that will diflash and select the appropriate type of mobile data is also done
Click the Flash button or Flash MCU Mod Lang or Flash or Flash GDFS or depending on the phone that is being done
How to unlock Z200 Unlock
In this case we can start by pressing the button on the UFS3 Tornado Init Locks
Mereflash followed by re-file "Z200_cust_std.bis by pressing the flash button on the program UFS3 Tornado cust
Or by setting the scenario for selecting Unlock column by pressing the Go button
Flashing Sony Ericsson Z200 Series Type ATRZ
Enter the file or data language such as 200_126734_r6c_con3.bis in Part1 and Part2 200_126734_r6c_fix3 at
Connect the phone with box and press the Go Flasher
Wait until the finish, to end press the Stop button and the phone ready to be released
Flashing Sony Ericsson T610 series RTP Type
Enter the MCU file such as a modem and a file T610_132233_r4c003_Emea6.bis T610_132233_r4c003_modem.bih
Select the column MCU scenario Modem
Connect phone and press the Go button, wait until the process is complete
Click Stop to release phones
Using tips and tricks on Samsung UFS3 Tornado
Make sure your phone is connected well with UFS3 Tornado Box
Click Connect button located on the top left of the program
Choose a type mobile phone that will diflash and select the appropriate type of mobile data is also done
Enter Flasher files according to the type of phones that work
Remove the battery (flash without battery)
Press the button 'Write Flash' is contained in the program and continue UFS3 Tornado by pressing the 'on' on the phone until the flame jgn
Wait until flash process finished
To type a specific phone or cell phone battery while still mounted on the flash time
Hopefully Helpful
Tornado UFS TECHNIQUES
Tips and tricks Using Nokia UFS3 Tornado On
In the case of 1st Boot Err or Bad Resp DCT3
Such damage is not usually occur because the phone connection of the Box
Check Flasher cable is used, because there is no possibility of being cut off point
If the cable is in good condition, there is the possibility of damage on the software UFS3
Reinstall the program with data that is still nice
Contact Service at Case
Damage like this is usually because they damage the data
Make a data deletion process with Erase FLASH
Then do flashing with the data is still good
Put a tick in the UI Options and click the Settings button UI
If there is damage to the IMEI data, do the Rebuild IMEI and repeat the process UI Settings
If the damage due to hardware, there are some IC that causes it, but cases like this simply by replacing the IC or IC Audio COBBA
If sata or Erasing Flashing process, the process stalled
Check Flasher cable, because it shows the relationship between the disconnection of telephone service provider with Flasher Box
Repeat process with reducing speed Speed Flasher
If it still stops at the same position repeatedly, there is the possibility of disturbance Flash IC
In case of contact Phone failed blimking retailer or on the phone type of WD2
Make sure your phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run programs for Nokia phones and select the type of WD2
Choose a type mobile phone that is being repair
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button to make sure Chek phone had been connected "Boot Ok"
In the UI Settings tab select Normal column, wait until the Normal Mode Ok
After appearing on the screen Normal Mode Ok continue by pressing the Format User Area
Finish Process
Practical Solutions Contact retailer or Blimking on your Nokia 6600
If this happens Flashing Erase error
Click Erase FLASH with the provisions of the Start Address and End Address 027FFFFF 02000000
If there Erase Flash Error then have to replace the flash IC No. 2, of the four existing IC
If the process successfully, but when switched on is still on the Contact retailer
Raise battry and plug in, then press the Call button in a cell phone or green button * number three in the mobile phone by simply pressing buttons simultaneously, without the use simcard
After the above step has been done, then the phone will do formating
After doing the formatting, mobile phones have been ready for use
In the case of Simcard Rejected or Simcard rejected a common cell phone types and DCT-4 WD2
Make sure your phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run programs for Nokia phones and select the type or DCT-4 WD2
Choose a type mobile phone that is being repair
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button to make sure Chek phone had been connected "Boot Ok"
In the UI Settings column select Normal, Normal Mode Ok wait until
After appearing on the screen Normal Mode Ok proceed by giving the tick on the Init Simlocks contained in the columns UI Options
Then click the Settings button until you see the UI on the screen Ok Init Simlock
In the case of No Charging and No Signal On Cell Phone and DCT type-4 WD2
Make sure your phone is connected well with UFS3 Tornado Box
UFS3 Tornado Run programs for Nokia phones and select the type or DCT-4 WD2
Choose a type mobile phone that is being repaired
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Chek Click the button to make sure the phone had been connected "Boot Ok"
In the UI Settings tab select Normal column, wait until the Normal Mode Ok
Click the button write pm (Wr PM), only one times with the provisions have saved PM file from each phone in the directory (c: \ Program Files \ Nokia \ Phoenix \ Products)
Wait until the process is complete
Phone Locks To overcome the problem of the phone type Nokia
Make sure your phone is connected well with UFS3 Tornado Box
Run the program for the Nokia UFS3 Tornado
Choose a type mobile phone that is locked or the phone lock
Click Connect button to liaison between the Box UFS3 Tornado with Computers
Click the button to make sure Chek phone had been connected "Boot Ok"
Tick tick on Full Factory Devaults contained in the columns UI Options
Then click the Settings button until you see the UI on the screen Full Factory Devaults Ok
Using tips and tricks UFS3 Tornado On Sony Ericsson phones
Practical Ways Sony Ericsson Flashing
Make sure your phone is connected well with UFS3 Tornado Box
Click Connect button located on the top left of the program
Battery not installed first before pressing the ON button, after pressing ON button you install a new battery, wait until everyone reads all phone information
Choose a type mobile phone that will diflash and select the appropriate type of mobile data is also done
Click the Flash button or Flash MCU Mod Lang or Flash or Flash GDFS or depending on the phone that is being done
How to unlock Z200 Unlock
In this case we can start by pressing the button on the UFS3 Tornado Init Locks
Mereflash followed by re-file "Z200_cust_std.bis by pressing the flash button on the program UFS3 Tornado cust
Or by setting the scenario for selecting Unlock column by pressing the Go button
Flashing Sony Ericsson Z200 Series Type ATRZ
Enter the file or data language such as 200_126734_r6c_con3.bis in Part1 and Part2 200_126734_r6c_fix3 at
Connect the phone with box and press the Go Flasher
Wait until the finish, to end press the Stop button and the phone ready to be released
Flashing Sony Ericsson T610 series RTP Type
Enter the MCU file such as a modem and a file T610_132233_r4c003_Emea6.bis T610_132233_r4c003_modem.bih
Select the column MCU scenario Modem
Connect phone and press the Go button, wait until the process is complete
Click Stop to release phones
Using tips and tricks on Samsung UFS3 Tornado
Make sure your phone is connected well with UFS3 Tornado Box
Click Connect button located on the top left of the program
Choose a type mobile phone that will diflash and select the appropriate type of mobile data is also done
Enter Flasher files according to the type of phones that work
Remove the battery (flash without battery)
Press the button 'Write Flash' is contained in the program and continue UFS3 Tornado by pressing the 'on' on the phone until the flame jgn
Wait until flash process finished
To type a specific phone or cell phone battery while still mounted on the flash time
Hopefully Helpful
